Dow Corning Silicone Oils

Dow-Corning-Q2 - 3387 Release Agent (Modified Silicone Fluid) : Silicone polymer Features:

No excessive cleaning required before finishing moulded parts

Excellent mould coverage (good wetting and spreading)

Heat stable

No build-up on moulds

No solvent : high flash point

Applications: Dow-Corning-Q2-3387 Release Agent has been specially formulated as a semi-permanent release agent in a wide range of applications, including:

Polyurethane Release: particularly polyester type, polyurethane shoe soles.

Micro-cellular automotive parts and furniture (integral skin).

Automotive parts: bumpers, crash-pads, dashboards.

Typical Properties: Specification writers: These values are not intended for use in preparing specifications. Please contact your local Dow Caning sales representative prior in writing specifications on this product-

CTM*	Parameter	Unit	Value
862	Active material content	%w/w	100
176	Appearance (visual)		Clear colourless liquid
4	Viscosity at 25°C	mm²/s	140
6	Flash point - closed cup	°C	>250
	Diluent		Aliphatic, aromatic, chlorinated hydrocarbons

*CTM: Corporate Test Method, copies of CTMs are available on request. How to Use? DOW Corning Q2-3387 Release Agent (1 part w/w) is normally diluted with a solvent (10 parts w/w) before application by spraying or brushing on the mould. Suitable solvents include most aliphatic, aromatic or chlorinated hydrocarbons. Users are recommended to determine optimum concentration and application method on a small test sample before use in production. Handling Precautions: Product safety information required for safe use is not included.

Features • Water-clear silicone fluid available in viscosity ranging from 0.65 to 60,000 cst (mm²/s) • Little change in physical properties over a wide temperature span - a relatively flat viscosity-temperature slope, and serviceability from -40°C up to 200°C • Excellent water repellent • Good dielectric properties over a wide range of temperatures and frequencies Low surface tension - readily wets clean surfaces to impart water repellent and release characteristics • Viscosity above 10 mm²/s also exhibit heat stability, oxidation resistance, very low vapor pressures, and high flash point • Low order of toxicity • Essentially odorless • Soluble in a wide range of solvents • Non-greasy and non-rancidifying Potydimethylsiloxane Applications: Release Material: Used alone or as part of a compounded formula, DOW Corning 200 Fluid provides a non-carbonizing mould release for rubber, plastics, and metal die castings. Foam Preventative: Extremely small amounts of the fluid effectively control foam in many processing operations, especially in non-aqueous systems. Mechanical Fluid: Excellent viscosity-temperature characteristics, thermal and chemical stability, shear-breakdown resistance, compressibility, and rubber compatibility make DOW Corning 200 Fluid outstanding for mechanical/ hydraulic uses. Typical uses include hydrolic stabilisers, damping media. Surface-Active Material: Added to vinyl plastisols, DOW Corning 200 Fluid improves the flow characteristics, de-aerates and lubricates me surface of the completed part. Lubricant: The fluid provides excellent lubrication for most plastic and elastomeric surfaces. Lubricity with metals depends upon the combination involved. Care should be taken to select suitable metals for pumps and other items with moving parts.

Release agent for molding, extruding and fabricating rubber and plastic parts, and in die casting metals Features

Compatible with most organic coatings and adhesive systems

Provides a heat-stable film

Does not require unusual or extraordinary cleaning operations prior to painting, plating or bonding

Composition Alkylaryl polysiloxane fluid Uses Dow Corning® 203 Fluid can be used for a wide variety of applications. It can be used for the production of floor mats and tiles, seals, grommets, gaskets, toys, paneling, decorative trim, household appliance assemblies, and similar plastic or rubber products that are coaled, painted, plated or bonded. It is also highly effective as a parting agent in die casting aluminum, zinc, magnesium and other metals. In addition, Dow Corning 203 Fluid can be used as an additive in rubber and plastic formulations. When added as a built-in lubricant, the fluid facilitates the assembly of mechanical components and acts as a lubricant in service. Typical Properties: These values are not intended for use in preparing specifications.

Test	Unit	Result
Physical Form		Pourable liquid
Color, APHA, maximum		150
Specific Gravity at 25°C (77°F)		0.91
Viscosity at 25°C(77°F)	cs	1400
Refractive Index at 25°C (77°F)		1.464
Flash Point, Pensky-Martin closed cup, minimum		93 (200)

Specification Writers: Please obtain a copy of the Dow Corning Sales Specification for this product and use it as a basis for your specifications. It may be obtained from any Dow Coming Sales Office, or from Dow Corning Customer Service in Midland, MI. Call (517) 496-6000.

Head stabilized polydimethylsiloxane DOW CORNING 210H Fluid ( Heat Stabilized Silicone Fluid ) Features:

Dimethyl silicone fluid with improved oxidation stability

Minimal viscosity change when subjected to severe heal and shear stresses

Applications: Mechano-fluid devices and controls. Heat transfer fluid in oil baths. Typical Properties: Specification writers: These values are not intended for use in preparing specifications. Please contact your local Dow Corning sales representative prior to writing specifications on this product.

Parameter	Unit	Value
Flash point - open cup	°C	>288
Pour point (ASTM D-97)1	°C	-65
Specific gravity at 25°C /15.6°C		0.96
Viscosity at 25°C	Cst	100
Viscosity-temperature coefficient, 1- (viscosity at 99°C / viscosity at 38°C)		0.6
Coefficient of expansion per °C unit volume/unit volume		0.00095
Vapour pressure at 204°C	pa	~330
Thermal conductivity at 25°C, W/m.K²		0.11
Volatility, % weight loss³		<2
Specific heat at 98.8°C	J/kg.K	1423

1: Apparently due to super-cooling, this test method yields pour points lower than the temperatures at which this silicons fluid would freeze if held at such temperature for a longer period. 2: Temperature gradient of l°C per cm thickness. 3: 35-40 grammes of fluid in a beaker having approximately a 20 cm² bottom area, heated in an air-circulating oven for 48 hours at 204°C.

Applications: • HydrophoHng treatment of plasterboard and plaster blocks. • Treatment for powders and granuJar materials to make them water repellent and free flowing, and to reduce caking. Typical Properties: Specification writers: These values are not intended for use in preparing specifications. Please contact your local Dow Corning sales representative prior ig writing specifications on this product. HOW TO USE DOW CORNING 1107 Fluid Is usually applied from dilute solution. Solutions are prepared by diluting DOW CORNING 1107 Fluid with hydrocarbon solvents, acetone or methyl ethyl ketone (see Handling Precautions), and stirring the mixture gently until uniform. The extent of dilution wili depend on the surface to be treated and surface properties desired. Curing Coatings of DOW CORNING 1107 Fluid are usually heat cured to develop release properties or water repellency. Curing temperatures range from 120°C to 175°C. Curing times are much shorter al higher curing temperatures. Catalysts are often used to accelerate cure. Foursuiiable catalysts in order of Increasing activity include zinc octoate (22% zinc), iron octoate (6% iron), dibutyl tin dilaurate, and tin octoates (28% tin). A typical catalyst concentration is one part catalyst, as supplied, to 10 parts of DOW CORNING 1107 Fluid.

Tetrasulfidosilane coupling agent for silica filled rubber. Features: Sulfur functional silane Reactive in sulfur-vulcanized rubber Benefits: Provides compatibility and coupling between inorganic fillers and organic rubber (e.g. silica and SBR) Composition: (EtO)3Si(CH2)3-Sx-(CH2)3Si(OEt)3 x~3.75 Applications: Coupling agent for inorganic fillers in organic rubber (such as silica in black rubber used in tire treads) Typical Properties: Specification Writers: These values are not intended for use in preparing specifications. Please contact your local Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product

Test	Unit	Result
Appearance		clear, amber liquid
Sulfur content	%	22.7
Average Sulfur Chain Length		3.75

Description Dow Corning® Z-6940 Silane is a mixture of polysulfidosilane species with an average sulfur chain length of 3.75. It is a 100% actives product in a liquid form. How to Use As with any organofunctional alkoxysilane coupling agent, Dow Canting Z-6940 Silane can be applied as a primer or incorporated in-situ in a compound formulation. As a primer of a surface, the silane can be dispersed in ethanol at about 1% and wiped onto a substrate. As an in-situ treatment, the silane is typically added with the organic matrix and inorganic filler/reinforcement. In the case of black rubber, oil silane is added with the rubber, oil and silica in the first mix. The ethoxysilyl groups then react to the surface of the inorganic material during this mix. It is typical to drive the temperature of the mixture to over 150°C to get adequate reaction of the silane to the filler.

We have speciality Silicone masterbatches from Dow Corning for WIRE AND CABLE INDUSTRY for both PVC and NON PVC base.

Product : Silicone Based Performance Additive for Thermoplastic Industry

SLIP, PRINT & LAMINATION - 3 IN ONE EFFECT

Recommended Use :
PP, HDPE ,LLDPE, LDPE, EVA

Standard Application : 
Packaging Film (Mono / Multi layer, Transparent / Opaque )

Process :
Extrusion / Moulding

Observed Outcome :
Increased productivity & Output, reduce Cycle time & wastages , Excellent Surface finish, Easy Mould release , Gloss

Dosage:
0.3% to 0.5%

Unique Features :
Dry, free flowing pallets with appropriate active for proper dispersion